FS Switche: Unterschied zwischen den Versionen
Aus d0b
Zur Navigation springenZur Suche springenSysd0b (Diskussion | Beiträge) |
Sysd0b (Diskussion | Beiträge) |
||
(18 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt) | |||
Zeile 1: | Zeile 1: | ||
== Allgemein == | == Allgemein == | ||
+ | |||
=== Terminal Settings === | === Terminal Settings === | ||
* Symbolrate von 1200 bis 115200 (default 9600) | * Symbolrate von 1200 bis 115200 (default 9600) | ||
Zeile 7: | Zeile 8: | ||
* flow control set to Xon/Xoff | * flow control set to Xon/Xoff | ||
− | mit Screen | + | mit Screen sieht das dann so aus: |
− | |||
<pre> | <pre> | ||
screen /dev/cu.usbserial 115200,cs8,-parenb,-cstopb,-clocal | screen /dev/cu.usbserial 115200,cs8,-parenb,-cstopb,-clocal | ||
</pre> | </pre> | ||
− | + | === Console === | |
+ | Rechte Level | ||
+ | <pre> | ||
+ | Switch> // | ||
+ | Switch# // Privileged EXEC Mode | ||
+ | Switch(config)# // Global Configuration Mode | ||
− | + | quit/exit // Aktuelles Rechtelevel bzw. Switch verlassen | |
+ | |||
+ | |||
+ | "enable" -> "configure terminal" | ||
+ | | \-------------------- switch to "Global Configuration Mode" | ||
+ | | | ||
+ | \------------------------------------ switch to "Privileged EXEC Mode" | ||
+ | </pre> | ||
+ | |||
+ | '''Show Configuration''' | ||
<pre> | <pre> | ||
− | + | show management ip address // Default: 192.168.1.10/24 | |
+ | show management ipv6 address | ||
+ | show interface status | ||
</pre> | </pre> | ||
− | + | '''Basic Configuration''' | |
− | |||
<pre> | <pre> | ||
− | + | hostname name // Hostnamen setzen | |
− | + | ||
− | + | management ip address A.B.C.D/M |A.B.C.D mask) (gateway A.B.C.D) // IPv4-Adresse für Netzwerk Management setzen | |
+ | management ip address 192.168.1.10/24 // Beispoel ohne GW | ||
+ | management ipv6 address (X:X::X:X/M | X:X::X:X mask) (gateway X:X::X:X) // IPv6-Adresse für Netzwerk Management setzen | ||
+ | enable password | ||
− | |||
</pre> | </pre> | ||
+ | ''' | ||
+ | Basic VLAN''' | ||
+ | <pre> | ||
+ | conf t | ||
+ | interface vlan 1 | ||
+ | no ip address dhcp // DHCP CLient abschalten | ||
+ | ip address 192.168.23.23 255.255.255.0 | ||
+ | copy running-config startup-config // config speichern | ||
+ | </pre> | ||
+ | |||
− | + | ==== LACP Dynamic ==== | |
+ | Eingaben im Global Configuration Mode "(config)#" | ||
<pre> | <pre> | ||
− | + | lacp system-priority 2000 | |
− | + | port-channel dynamic-load-balance enable | |
+ | interface eth-0-1 | ||
+ | no shutdown | ||
+ | channel-group 1 mode active | ||
+ | exit | ||
+ | interface eth-0-2 | ||
+ | no shutdown | ||
+ | channel-group 1 mode active | ||
+ | exit | ||
+ | interface agg 1 | ||
+ | jumboframe enable // MTU anpassen | ||
+ | exit | ||
+ | |||
+ | copy running-config startup-config // config speichern | ||
+ | |||
+ | |||
+ | |||
+ | show channel-group summary // config prüfen | ||
+ | show interface agg 1 | ||
+ | show lacp {counters | internal | neighbor | sys-id} | ||
</pre> | </pre> | ||
== Produke == | == Produke == | ||
+ | === S1600-48T4S === | ||
+ | |||
+ | |||
+ | === S3400-48T4SP === | ||
+ | * [https://www.fs.com/de/products/90132.html Product Page] | ||
+ | |||
+ | * Fiberstore Co., Limited Internetwork Operating System Software Version 2.2.0J Build 68107, | ||
+ | |||
+ | Abweichende CLI Befehle! | ||
+ | <pre> | ||
+ | config // Global Configuration Mode | ||
+ | write // Speichern | ||
+ | </pre> | ||
+ | |||
=== S5800-8TF12S === | === S5800-8TF12S === | ||
* [https://www.fs.com/de/products/69404.html S5800-8TF12S Product Page] | * [https://www.fs.com/de/products/69404.html S5800-8TF12S Product Page] | ||
* [https://img-en.fs.com/file/user_manual/fs-s5800-8tf12s-mibs.zip S5800-8TF12S MIBs] | * [https://img-en.fs.com/file/user_manual/fs-s5800-8tf12s-mibs.zip S5800-8TF12S MIBs] | ||
+ | |||
+ | |||
+ | ==== Default Login ==== | ||
+ | * User: admin | ||
+ | * Password: admin |
Aktuelle Version vom 21. April 2020, 15:51 Uhr
Inhaltsverzeichnis
Allgemein
Terminal Settings
- Symbolrate von 1200 bis 115200 (default 9600)
- 8 data bits
- 1 stop bit
- no parity
- flow control set to Xon/Xoff
mit Screen sieht das dann so aus:
screen /dev/cu.usbserial 115200,cs8,-parenb,-cstopb,-clocal
Console
Rechte Level
Switch> // Switch# // Privileged EXEC Mode Switch(config)# // Global Configuration Mode quit/exit // Aktuelles Rechtelevel bzw. Switch verlassen "enable" -> "configure terminal" | \-------------------- switch to "Global Configuration Mode" | \------------------------------------ switch to "Privileged EXEC Mode"
Show Configuration
show management ip address // Default: 192.168.1.10/24 show management ipv6 address show interface status
Basic Configuration
hostname name // Hostnamen setzen management ip address A.B.C.D/M |A.B.C.D mask) (gateway A.B.C.D) // IPv4-Adresse für Netzwerk Management setzen management ip address 192.168.1.10/24 // Beispoel ohne GW management ipv6 address (X:X::X:X/M | X:X::X:X mask) (gateway X:X::X:X) // IPv6-Adresse für Netzwerk Management setzen enable password
Basic VLAN
conf t interface vlan 1 no ip address dhcp // DHCP CLient abschalten ip address 192.168.23.23 255.255.255.0 copy running-config startup-config // config speichern
LACP Dynamic
Eingaben im Global Configuration Mode "(config)#"
lacp system-priority 2000 port-channel dynamic-load-balance enable interface eth-0-1 no shutdown channel-group 1 mode active exit interface eth-0-2 no shutdown channel-group 1 mode active exit interface agg 1 jumboframe enable // MTU anpassen exit copy running-config startup-config // config speichern show channel-group summary // config prüfen show interface agg 1 show lacp {counters | internal | neighbor | sys-id}
Produke
S1600-48T4S
S3400-48T4SP
- Fiberstore Co., Limited Internetwork Operating System Software Version 2.2.0J Build 68107,
Abweichende CLI Befehle!
config // Global Configuration Mode write // Speichern
S5800-8TF12S
Default Login
- User: admin
- Password: admin